|
5.2.7 problems with grinding restorations on Primemill
By:
Andrew Dunn-King
3 Replies
|
3 |
50 |
May 26th, 2023
By: Peter Gardell
|
|
Sidexis 4 - exporting CBCT
By:
Andrew Dunn-King
7 Replies
|
7 |
92 |
June 27th, 2022
By: Andrew Dunn-King
|
|
SpeedFire back up cycles
By:
Andrew Dunn-King
|
0 |
47 |
September 8th, 2021
By: Andrew Dunn-King
|
|
Designing multiple restorations and sending to manufacture
By:
Andrew Dunn-King
3 Replies
|
3 |
62 |
July 4th, 2021
By: Andrew Dunn-King
|
|
Maryland bridge with Primemill
By:
Andrew Dunn-King
3 Replies
|
3 |
89 |
May 4th, 2021
By: Mark Fleming
|
|
Emax fast mill with Primescan/Primemill
By:
Andrew Dunn-King
2 Replies
|
2 |
72 |
March 22nd, 2021
By: Andrew Dunn-King
|
|
Sand blaster chair side
By:
Andrew Dunn-King
5 Replies
|
5 |
110 |
February 27th, 2021
By: John Toccafondi
|
|
Spanish implant aura evo np 3.5
By:
Andrew Dunn-King
|
0 |
17 |
January 6th, 2019
By: Andrew Dunn-King
|
|
Cerec Premium - designating adjacent bridges
By:
Andrew Dunn-King
1 Reply
|
1 |
43 |
August 29th, 2018
By: Ross Enfinger
|
|
Scanbody folder needing manual stitching with other folder
By:
Andrew Dunn-King
1 Reply
|
1 |
42 |
April 7th, 2018
By: Marc Thomas
|
|
Sintering multiple zironia crowns in Speedfire
By:
Andrew Dunn-King
4 Replies
|
4 |
120 |
February 19th, 2018
By: Dave Rossen
|
|
Milling multiple crowns out bridge zirconia block
By:
Andrew Dunn-King
|
0 |
43 |
January 10th, 2018
By: Armin Giessmann
|
|
Biomet 3i abutment driver for TiBase
By:
Andrew Dunn-King
4 Replies
|
4 |
59 |
September 5th, 2014
By: Andrew Dunn-King
|
|
TiBase for Branemark WP
By:
Andrew Dunn-King
1 Reply
|
1 |
27 |
August 4th, 2014
By: Marc Thomas
|
|
3D printed model from Sirona CBCT
By:
Andrew Dunn-King
4 Replies
|
4 |
132 |
June 12th, 2014
By: Michael Ravens
|
|
Galaxis findings tab - preset notes
By:
Andrew Dunn-King
|
0 |
32 |
March 12th, 2014
By: Andrew Dunn-King
|
|
CBCT maxillary sinus pathology
By:
Andrew Dunn-King
3 Replies
|
3 |
91 |
December 18th, 2013
By: Andrew Dunn-King
|
|
Storage of Bio-Oss and Bio-Gide
By:
Andrew Dunn-King
1 Reply
|
1 |
34 |
October 16th, 2013
By: Farhad Boltchi
|
|
Can I upload Galileos/Cerec case for the group to comment on?
By:
Andrew Dunn-King
10 Replies
|
10 |
106 |
September 6th, 2013
By: Paul Caselle
|
|
Importing into inlab
By:
Andrew Dunn-King
8 Replies
|
8 |
88 |
October 2nd, 2012
By: Hugh Fleming
|
|
First inLab 4.0.1 abutment and crown upper lateral incisor case
By:
Andrew Dunn-King
|
0 |
40 |
September 6th, 2012
By: Andrew Dunn-King
|
|
Stack milling
By:
Andrew Dunn-King
1 Reply
|
1 |
48 |
August 24th, 2012
By: Bob Conte
|
|
Vita Vacumat 6000M eMax setting
By:
Andrew Dunn-King
2 Replies
|
2 |
61 |
July 5th, 2012
By: Andrew Dunn-King
|