|
|
4.4 will not save restoration
By:
dennis stolzenburg
6 Replies
|
6 |
62 |
March 24th, 2016
By: Mark Fleming, D.D.S.
|
|
|
order scan post and tibase
By:
dennis stolzenburg
2 Replies
|
2 |
46 |
February 1st, 2016
By: dennis stolzenburg
|
|
|
how to forward thru to mill stage
By:
dennis stolzenburg
3 Replies
|
3 |
92 |
December 4th, 2014
By: Marc Thomas
|
|
|
emax debond
By:
dennis stolzenburg
11 Replies
|
11 |
280 |
November 17th, 2014
By: Blue Davis
|
|
|
biocopy case models will not correlate.
By:
dennis stolzenburg
6 Replies
|
6 |
94 |
October 2nd, 2014
By: dennis stolzenburg
|
|
|
lost model part with trim tool
By:
dennis stolzenburg
8 Replies
|
8 |
87 |
August 22nd, 2014
By: Steve Nielsen
|
|
|
location of crown in block
By:
dennis stolzenburg
5 Replies
|
5 |
104 |
August 12th, 2014
By: dennis stolzenburg
|
|
|
support emax bridge during firing
By:
dennis stolzenburg
1 Reply
|
1 |
61 |
July 2nd, 2014
By: Steven Hernandez
|
|
|
wrong tooth # on models
By:
dennis stolzenburg
8 Replies
|
8 |
131 |
April 7th, 2014
By: dennis stolzenburg
|
|
|
software wont advance
By:
dennis stolzenburg
9 Replies
|
9 |
95 |
March 10th, 2014
By: Ernie Johnson
|
|
|
glue down emax
By:
dennis stolzenburg
16 Replies
|
16 |
313 |
October 7th, 2013
By: dennis stolzenburg
|
|
|
no mesial contact shown
By:
dennis stolzenburg
6 Replies
|
6 |
113 |
October 3rd, 2013
By: dennis stolzenburg
|
|
|
help with prior post
By:
dennis stolzenburg
3 Replies
|
3 |
67 |
September 16th, 2013
By: Steve Nielsen
|
|
|
can't stitch models, can't do in biocopy
By:
dennis stolzenburg
|
0 |
56 |
September 15th, 2013
By: dennis stolzenburg
|
|
|
first 3 unit bridge
By:
dennis stolzenburg
6 Replies
|
6 |
178 |
September 11th, 2013
By: Dave Juliani
|
|
|
no contact indication on mesial
By:
dennis stolzenburg
1 Reply
|
1 |
59 |
August 28th, 2013
By: Mike Skramstad
|
|
|
bio copy vs. engineered occlusion,
By:
dennis stolzenburg
12 Replies
|
12 |
189 |
February 27th, 2013
By: Steve Nielsen
|
|
|
poor biocopy proposal
By:
dennis stolzenburg
4 Replies
|
4 |
96 |
February 27th, 2013
By: dennis stolzenburg
|
|
|
solid "block" proposal
By:
dennis stolzenburg
5 Replies
|
5 |
94 |
June 13th, 2012
By: dennis stolzenburg
|
|
|
cyclic redundancy check
By:
dennis stolzenburg
8 Replies
|
8 |
65 |
May 9th, 2012
By: Bianca Malin
|
|
|
error message cyclic redundancy check
By:
dennis stolzenburg
|
0 |
18 |
May 8th, 2012
By: dennis stolzenburg
|
|
|
cannot create virtual model...alignment aid dots
By:
dennis stolzenburg
4 Replies
|
4 |
70 |
April 29th, 2012
By: dennis stolzenburg
|
|
|
vid card?
By:
dennis stolzenburg
8 Replies
|
8 |
5 |
December 12th, 2011
By: dennis stolzenburg
|
|
|
submerged teeth in model
By:
dennis stolzenburg
8 Replies
|
8 |
1 |
December 6th, 2011
By: Mike Skramstad
|
|
|
crummy correlation proposals.
By:
dennis stolzenburg
10 Replies
|
10 |
4 |
June 13th, 2011
By: Jeffrey Caso
|
|
|
sprue on margin
By:
dennis stolzenburg
3 Replies
|
3 |
2 |
February 9th, 2011
By: Steve Nielsen
|
|
|
"air bubble" on model margin
By:
dennis stolzenburg
6 Replies
|
6 |
3 |
November 13th, 2010
By: Sameer Puri D.D.S.
|
|
|
poor proposal new software
By:
dennis stolzenburg
|
0 |
1 |
August 18th, 2010
By: dennis stolzenburg
|
|
|
bond failure rebond
By:
dennis stolzenburg
5 Replies
|
5 |
4 |
June 10th, 2010
By: Rich Rosenblatt, D.M.D.
|
|
|
margin breakage, sprue on margin
By:
dennis stolzenburg
3 Replies
|
3 |
0 |
May 6th, 2010
By: dennis stolzenburg
|
