|
re-bonding?
By:
Blake Winokur
2 Replies
|
2 |
75 |
September 26th, 2022
By: Gary Templeman
|
|
adjusting occlusion before or after cement?
By:
Blake Winokur
4 Replies
|
4 |
139 |
July 15th, 2022
By: Catherine Cech
|
|
sintering zirconia +
By:
Blake Winokur
2 Replies
|
2 |
55 |
January 26th, 2022
By: Dave Rossen
|
|
cerasmart occlusal offset?
By:
Blake Winokur
7 Replies
|
7 |
86 |
January 5th, 2022
By: Brett Titensor
|
|
treating EMax
By:
Blake Winokur
15 Replies
|
15 |
231 |
May 22nd, 2021
By: Grady Twohig
|
|
hard/soft occlusal guard
By:
Blake Winokur
2 Replies
|
2 |
97 |
November 16th, 2020
By: Rohini Singh
|
|
remove bonded Emax from Atlantis abutment?
By:
Blake Winokur
1 Reply
|
1 |
47 |
July 25th, 2020
By: Dan Butterman, D.D.S.
|
|
Bridge to long to mill...now what?
By:
Blake Winokur
5 Replies
|
5 |
105 |
May 29th, 2020
By: Michael Mingle
|
|
suresmile aligner question
By:
Blake Winokur
7 Replies
|
7 |
135 |
March 6th, 2020
By: Sathvik Seshadri
|
|
Printing out hybrid - can't get a "model" please help
By:
Blake Winokur
7 Replies
|
7 |
76 |
December 4th, 2019
By: Blake Winokur
|
|
New to Primescan - contacts question
By:
Blake Winokur
5 Replies
|
5 |
127 |
November 10th, 2019
By: Blake Winokur
|
|
Quality label not recognized on Katana please help!
By:
Blake Winokur
6 Replies
|
6 |
36 |
October 9th, 2019
By: Blake Winokur
|
|
Bleach shade blocks
By:
Blake Winokur
5 Replies
|
5 |
89 |
September 20th, 2019
By: Blake Winokur
|
|
Crown cut off with 40 seconds left to mill
By:
Blake Winokur
3 Replies
|
3 |
74 |
July 29th, 2019
By: Blake Winokur
|
|
proximal contact strength
By:
Blake Winokur
4 Replies
|
4 |
53 |
July 18th, 2019
By: Blake Winokur
|
|
Emax crown fx. 2X in oven, same spot
By:
Blake Winokur
3 Replies
|
3 |
78 |
July 10th, 2019
By: Thad Vincent
|
|
Step Bur 12 S is defective
By:
Blake Winokur
6 Replies
|
6 |
95 |
May 22nd, 2019
By: Blake Winokur
|
|
Cerec Zirconia
By:
Blake Winokur
17 Replies
|
17 |
190 |
May 20th, 2019
By: Dave Rossen
|
|
EMax bleach shade?
By:
Blake Winokur
3 Replies
|
3 |
73 |
May 12th, 2019
By: Charles Lo Giudice
|
|
EMax cantilever 10 and 11
By:
Blake Winokur
1 Reply
|
1 |
54 |
May 11th, 2019
By: Mark Fleming, D.D.S.
|
|
micro etch zirconia
By:
Blake Winokur
1 Reply
|
1 |
45 |
April 29th, 2019
By: Mark Fleming, D.D.S.
|
|
printing occlusal guards
By:
Blake Winokur
11 Replies
|
11 |
183 |
March 6th, 2019
By: Ray Morse
|