CDOCS Workshops will resume as scheduled beginning in July. LEARN MORE
CEREC Doctors

Discussion Boards

Michael Costa Post a New Topic

Date Title
21 ext, graft, implant, screw retained crown - please tell me where i can improve
By: Michael Costa 4 Replies
can i substiute for monobond plus when bonding to a ti base?
By: Michael Costa 1 Reply
need help with 1st split case - almost there
By: Michael Costa 1 Reply
need help with 1st split case
By: Michael Costa 5 Replies
adjacent splinted posterior implant crowns
By: Michael Costa 2 Replies
electrical issues - power failure
By: Michael Costa 2 Replies
can you "overcook" a restoration?
By: Michael Costa 2 Replies
implant compatability question - alpha bio titan implants?
By: Michael Costa 1 Reply
Reusing a block
By: Michael Costa 3 Replies
we're still taking alginates for bleaching trays, custom trays, night guards - can i stop?
By: Michael Costa 13 Replies
can i do katana bridge blocks with an upgraded omni, 5.1 and mcxl?
By: Michael Costa 2 Replies
finally got my 5.1 omni and window 10 upgrade - will my parameters carry over?
By: Michael Costa 2 Replies
light contact on the last tooth in the arch?
By: Michael Costa 11 Replies
"sensitive to when i chew things that mold to the tooth - like gum or meat - but not all the time"
By: Michael Costa 4 Replies
first implant crown start to finish
By: Michael Costa 6 Replies
can i mill a replacement denture tooth?
By: Michael Costa 9 Replies
teflon to retract?
By: Michael Costa 5 Replies
really bad veneer propoal
By: Michael Costa 6 Replies
minimal thickness on implant crown
By: Michael Costa 4 Replies
ordering an implant block #31 emax screw retained
By: Michael Costa 5 Replies
trusting the virtual articluator
By: Michael Costa 2 Replies
Broken door
By: Michael Costa 7 Replies
prepping 31 and scanning an upper comlete denture as opposing model
By: Michael Costa 2 Replies
twsit polishers
By: Michael Costa 2 Replies
katana sizing question
By: Michael Costa 2 Replies
can i mill 2 single units from a katana bridge block?
By: Michael Costa 2 Replies
designing a guide plane/rest seat for a planned partial
By: Michael Costa 3 Replies
implant bailout question - what's best to mill over cast ucla abutments
By: Michael Costa 4 Replies
anyone in NYC area do the upgrade to windows 10 and the 5.1 SW through schein??
By: Michael Costa 3 Replies
crown or onlay and keep the buccal wall
By: Michael Costa 5 Replies
Is there a way to screen capture live video on the cerec?
By: Michael Costa 3 Replies
micro etch question
By: Michael Costa 7 Replies
post op sensitvity - any suggestions
By: Michael Costa 17 Replies
single unit #2 FML...
By: Michael Costa 2 Replies
O or 0 - seriously???
By: Michael Costa 15 Replies
could i have scanned this?
By: Michael Costa 5 Replies
3 unit cerec zr bridge came off sprue early - burs kept miling air
By: Michael Costa 3 Replies
first maryland bridge 7 pontic / 8 retainer - thanks for all the design help
By: Michael Costa 4 Replies
Maryland bridge design help
By: Michael Costa 9 Replies
sandblasting/microetching setup
By: Michael Costa 8 Replies
tx planning help - anterior case
By: Michael Costa 7 Replies
fast vs fine milling
By: Michael Costa 4 Replies
Level 3 in Charlotte
By: Michael Costa 2 Replies
debonded onlay - should this have been full coverage?
By: Michael Costa 2 Replies
design help - zr bridge 12-14, error msg
By: Michael Costa 5 Replies
crown fell off the sprue towards the end of the milling cycle - burs kept on cutting
By: Michael Costa 4 Replies
block handling
By: Michael Costa 3 Replies
emax crown and core debonded - suggestions?
By: Michael Costa 5 Replies
metal allergies
By: Michael Costa 4 Replies
Milling unit error: detected measurments incorrect for right instrument. please ensure that...
By: Michael Costa 3 Replies