|
|
New Blue Sky Bio User. Few questions for designing guides.
By:
Trevor Labrum
1 Reply
|
1 |
86 |
February 23rd, 2020
By: Orest Bauer
|
|
|
Options for Zirconia Milling
By:
Trevor Labrum
2 Replies
|
2 |
57 |
November 25th, 2019
By: Trevor Labrum
|
|
|
Exact diameter of Cerec Guide 2 hole
By:
Trevor Labrum
11 Replies
|
11 |
84 |
September 12th, 2019
By: Trevor Labrum
|
|
|
Correct TiBase for Nobel Active 4.3 x 11.5mm
By:
Trevor Labrum
4 Replies
|
4 |
35 |
July 9th, 2019
By: Trevor Labrum
|
|
|
Couple of questions: where did biojaw go? Also any idea on how to make this case easier?
By:
Trevor Labrum
7 Replies
|
7 |
104 |
June 25th, 2019
By: Trevor Labrum
|
|
|
Help trying to figure out acceptable abutment design for split case...
By:
Trevor Labrum
3 Replies
|
3 |
40 |
May 9th, 2019
By: Trevor Labrum
|
|
|
Katana Blocks fracturing during mill?
By:
Trevor Labrum
9 Replies
|
9 |
129 |
February 27th, 2019
By: Trevor Labrum
|
|
|
Scanning and restoring side by side implants with TiBase
By:
Trevor Labrum
6 Replies
|
6 |
104 |
January 30th, 2019
By: Mark Fleming, D.D.S.
|
|
|
Issues with cropping of image files after correlation
By:
Trevor Labrum
1 Reply
|
1 |
30 |
January 15th, 2019
By: Trevor Labrum
|
|
|
Restoration question for Implant Direct
By:
Trevor Labrum
2 Replies
|
2 |
57 |
December 28th, 2018
By: Trevor Labrum
|
|
|
Question for you Cerec Guide 2 gurus...
By:
Trevor Labrum
11 Replies
|
11 |
86 |
December 11th, 2018
By: Trevor Labrum
|
|
|
Interesting #14 proposal, and BioJaw in 4.5 wasn't working too well to correct. Any tips?
By:
Trevor Labrum
2 Replies
|
2 |
69 |
August 31st, 2018
By: Trevor Labrum
|
|
|
Anyone had issues with the Zirconia Barcodes?
By:
Trevor Labrum
5 Replies
|
5 |
84 |
June 22nd, 2018
By: John Poston
|
|
|
Trouble with Straumann Variobase seats
By:
Trevor Labrum
20 Replies
|
20 |
195 |
August 14th, 2017
By: Carmela LaFalce
|
|
|
Help! Which selection do I make in 4.4 for a Straumann RN Variobase C?
By:
Trevor Labrum
2 Replies
|
2 |
45 |
June 12th, 2017
By: Trevor Labrum
|
|
|
Issue with Speedfire Oven turning itself off randomly...
By:
Trevor Labrum
8 Replies
|
8 |
106 |
November 3rd, 2016
By: Arthur Jordan
|
|
|
Implant course suggestions?
By:
Trevor Labrum
16 Replies
|
16 |
245 |
August 23rd, 2016
By: Judson Connell
|
|
|
TZI vs TZI C inCoris blocks
By:
Trevor Labrum
6 Replies
|
6 |
157 |
July 8th, 2016
By: Mike Skramstad
|
|
|
Adding glaze to PFM bridge with Ivoclar Oven
By:
Trevor Labrum
5 Replies
|
5 |
98 |
May 25th, 2016
By: Robert Feudo
|
|
|
Speedfire oven and bridges
By:
Trevor Labrum
7 Replies
|
7 |
153 |
May 24th, 2016
By: Trevor Labrum
|
|
|
Level 2 Assistant Outline
By:
Trevor Labrum
2 Replies
|
2 |
103 |
May 17th, 2016
By: Trevor Labrum
|
|
|
Help, pt in chair and the ti-base is going through the abutment, which will cause seating issues.
By:
Trevor Labrum
17 Replies
|
17 |
144 |
May 12th, 2016
By: Trevor Labrum
|
|
|
Question about eMax MO abutment blocks as well as TiBase
By:
Trevor Labrum
5 Replies
|
5 |
68 |
May 5th, 2016
By: Trevor Labrum
|
|
|
Help with a case.
By:
Trevor Labrum
7 Replies
|
7 |
95 |
April 26th, 2016
By: Mark Fleming, D.D.S.
|
|
|
Cost to upgrade Sirona Orthophos XG to 3d?
By:
Trevor Labrum
2 Replies
|
2 |
98 |
March 26th, 2016
By: Trevor Labrum
|
