|
|
Create screw access hole pre- or post-sintering for zirconia bridge?
By:
Brad Cruse
1 Reply
|
1 |
56 |
March 4th, 2021
By: Dan Butterman, D.D.S.
|
|
|
Incorporating Biocopy into Atlantis case with Prima Connex?
By:
Brad Cruse
5 Replies
|
5 |
47 |
December 18th, 2020
By: Dan Butterman, D.D.S.
|
|
|
Cerabien Glazing Schedule?
By:
Brad Cruse
4 Replies
|
4 |
71 |
December 3rd, 2020
By: Brad Cruse
|
|
|
Use aligners to distalize molar?
By:
Brad Cruse
8 Replies
|
8 |
153 |
November 12th, 2020
By: Gary Templeman
|
|
|
Undermilling in 5.1.2?
By:
Brad Cruse
3 Replies
|
3 |
102 |
October 8th, 2020
By: Mark Stockwell
|
|
|
Overmilling MCXL vs Primemill
By:
Brad Cruse
1 Reply
|
1 |
92 |
October 5th, 2020
By: Mark Fleming, D.D.S.
|
|
|
Use 3M zirconia for 4 unit anterior?
By:
Brad Cruse
3 Replies
|
3 |
85 |
September 4th, 2020
By: Andrew Hall
|
|
|
7. CEREC SW 5.1 - Parameters Part 5
By:
Brad Cruse
7 Replies
|
7 |
178 |
February 13th, 2020
By: Mark Fleming, D.D.S.
|
|
|
Mastering multiple pumpkin anteriors?
By:
Brad Cruse
13 Replies
|
13 |
232 |
October 31st, 2019
By: Marc Kaufman
|
|
|
Out of Object Fix, can I use Speed Paste for e.max?
By:
Brad Cruse
10 Replies
|
10 |
146 |
June 25th, 2019
By: Cecil Sandoval
|
|
|
Tx planning deep bite 80yo former hygienist
By:
Brad Cruse
10 Replies
|
10 |
135 |
May 21st, 2019
By: Rick Chapman
|
|
|
Troubleshoot wet milling zirconia
By:
Brad Cruse
8 Replies
|
8 |
59 |
February 20th, 2019
By: Charlie Hooper
|
|
|
Consensus on new motor for 2008 MCXL to wet mill zirconia?
By:
Brad Cruse
8 Replies
|
8 |
117 |
November 19th, 2018
By: Robert Feudo
|
|
|
Treatment planning suggestions?
By:
Brad Cruse
5 Replies
|
5 |
98 |
August 17th, 2018
By: Brad Cruse
|
|
|
Silane for Cerasmart?
By:
Brad Cruse
10 Replies
|
10 |
151 |
July 28th, 2018
By: Jeffrey Zaffos
|
|
|
for TelioCAD custom healer, call it e.max to have multilayer option for the final?
By:
Brad Cruse
3 Replies
|
3 |
54 |
February 23rd, 2018
By: Robert Lang
|
|
|
Which cab for lab microetching?
By:
Brad Cruse
6 Replies
|
6 |
73 |
February 23rd, 2018
By: Bruce Herr
|
|
|
unable to mill 24x26 e.max bridge without chipped and open margin
By:
Brad Cruse
3 Replies
|
3 |
80 |
November 2nd, 2017
By: Mark Fleming, D.D.S.
|
|
|
Full arch scanning with chairside SW, not Ortho
By:
Brad Cruse
5 Replies
|
5 |
78 |
September 8th, 2017
By: Brad Cruse
|
|
|
Immediate implant TelioCAD temp too buky on lingual
By:
Brad Cruse
2 Replies
|
2 |
75 |
November 4th, 2016
By: Mark Stockwell
|
|
|
9 yr old with congenitally missing 7/10 - what to do now?
By:
Brad Cruse
7 Replies
|
7 |
171 |
September 26th, 2016
By: David Edelson
|
|
|
Biostar or Erkoform?
By:
Brad Cruse
3 Replies
|
3 |
90 |
March 18th, 2016
By: David Edelson
|
|
|
photos 6x11 block selection?
By:
Brad Cruse
4 Replies
|
4 |
118 |
May 9th, 2015
By: Andrew Hall
|
|
|
D6065 for screw-retained e.max?
By:
Brad Cruse
2 Replies
|
2 |
115 |
April 4th, 2015
By: Brad Cruse
|
|
|
Anterior block: LT or Impulse to block out these cast posts?
By:
Brad Cruse
9 Replies
|
9 |
174 |
January 13th, 2015
By: Mark Stockwell
|
|
|
Why is there an open margin between my emax abutment and crown?
By:
Brad Cruse
3 Replies
|
3 |
165 |
January 5th, 2015
By: Brad Cruse
|
|
|
Impulse Cantilever bridge?
By:
Brad Cruse
2 Replies
|
2 |
84 |
November 13th, 2014
By: Charles Lo Giudice
|
|
|
Maryland bridge longevity
By:
Brad Cruse
3 Replies
|
3 |
87 |
May 15th, 2014
By: Brad Cruse
|
|
|
Maryland Bridge - prep or no prep, one or two wings?
By:
Brad Cruse
4 Replies
|
4 |
107 |
April 29th, 2014
By: Fred Giombolini
|
|
|
Lone molar infraocclusion
By:
Brad Cruse
5 Replies
|
5 |
95 |
January 28th, 2014
By: Steven Hernandez
|
|
|
Open mesial contact on distal-most tooth (twice)
By:
Brad Cruse
9 Replies
|
9 |
189 |
January 17th, 2014
By: Brad Cruse
|
|
|
Introral polishing steps and products
By:
Brad Cruse
2 Replies
|
2 |
101 |
January 14th, 2014
By: Brad Cruse
|
