CEREC Doctors

Discussion Boards

Manufacturer and Product Information Post a New Topic

A place to find information about digital dentistry products and their manufacturers.

Created Title
Scanning MIS C1 Implants
By: Todd Raphaelson 6 Replies
Transitional all on provisionals to provisional abutments
By: Mark Austin 2 Replies
Implant crowns OM3 shade
By: Todd Vincent
Firing Parameters?
By: Abby Dorias 3 Replies
help choosing scanpost for nobel NP 3.75 implant, restoring with emax in house
By: Casey Williams 2 Replies
Zirconia Blocks
By: Abby Dorias 1 Reply
Strauman BLX WB
By: Kristy Smith 2 Replies
Uploading a CBCT from Sidexis into DS Core to share
By: Andy Powell 5 Replies
Who makes the longest bridge block
By: Anissa Singratanakul 7 Replies
MultiPeg for Astra EV profile to assess ISQ
By: James Stuart 2 Replies
resin crown material for Cerec
By: Kevin Ward 9 Replies
Possible to mill 4 unit Zirconia with PrimeMill?
By: Laura Sass Meincke 1 Reply
Did anyone replace emax/tessera with ZirCad Prime for esthetic cases?
By: Sergei Shirman 2 Replies
Programat cs6
By: Richard Rogers 15 Replies
Expired resin PrimePrint
By: Kristi Coulombe 2 Replies
Cerec Support membership
By: Rashmi Bhatnagar 3 Replies
Go to chairside zirconia block material
By: Justin Straight 14 Replies
CS6 Custom Cycles
By: Ben Petry
treating tooth prior to cementation of ZR w RMGI
By: Brad Dorsch 4 Replies
calibrate primemill
By: Brad Dorsch 1 Reply
Ivoclar cs6 oven and celtra/tessera
By: michael bensky 4 Replies
aufbiss-schaum (bite blocks)
By: Matt Kime
Sirona InCoris Meso L - discontiuned?
By: Matt Kime 3 Replies
Good Dental Labs for printing Implant surgical guides
By: Brad Cherry 6 Replies
Long term temporary restorative materials
By: Joe Bousaba 4 Replies
PrimePrint Vats repurposing temp material shades
By: Randy Houska 2 Replies
Looking for a temporary bridge block
By: Felicia Napoleon 2 Replies
Primeprint Splint SF vs ST
By: Ryan Sill 7 Replies
Primeprint resin
By: Shane Ellsworth 2 Replies
Emax Staining and Glazing Products
By: Isabella Terrassa 4 Replies
Sirona inCoris material no longer supported after update
By: Cody Olson 3 Replies
Zirconium Implant Blocks
By: Robert Brown 7 Replies
prime print model resin
By: Michele Simpson 3 Replies
omnicam Invisalign
By: Sabry Sharara 2 Replies
Implant Replacement Screw
By: Alberto Taylor 6 Replies
Isses with Sprintray
By: Brett Skinner 3 Replies
Primescan Offload
By: Rio Naas 6 Replies
Straumann BLT SLActive Roxolid RC 4.0
By: Tavi Henry 1 Reply
trying to export a printable STL of the prep arch from the prim scan. ( I do not have in lab)
By: Eric Cornelius 4 Replies
GC Initial LiSi Block
By: Gabrielle Weishoff 6 Replies
Proper forum for purchasing used CEREC equipment
By: Jacob Blodgett 5 Replies
Ivoclar Cystall stain used alone?
By: AJ Majidian 1 Reply
"TLS initialization failed" warning appeared on my Primescan when bringing up software
By: Don Ratliff
TAG Robicone implants
By: Konstantin Pliev 1 Reply
Buyer beware on Butterfly needle sets
By: Doug Smail, D.D.S. 4 Replies
CS4 oven Zir coming out too light.
By: Kenneth Burson 1 Reply
Digital Denture Resin
By: Ray Kessler 4 Replies
CEREC Onlays
By: Dan Strobel 18 Replies
Is there ever a need to order the Midi CEREC guide blocks to mill the CEREC Guide 3
By: Islam Dehis 3 Replies
Substitute for inCoris Meso F2 S block
By: Cody Olson 9 Replies