Discussion Boards

General Discussion Post a New Topic

Here is the place to unwind and discuss anything.

Created Title
9.6% HFl vs. 5%?
By: K Michael Murphy 6 Replies
problem shade!!
By: Paul Wulff 4 Replies
Soft tissue material
By: Jay Henderson 7 Replies
Model size in 4.0
By: Paul Goodman 11 Replies
emax splinted 28-29 how to do using 4.01
By: Mark White 1 Reply
Connect License Drive?
By: Bob Conte 2 Replies
Importing a case from 3.85
By: Chris Tricinella 5 Replies
Design of a quadrant #30Biogeneric, #31 Biocopy
By: Jeffrey Erickson 3 Replies
Motor problem???
By: William Cardman 3 Replies
biocopy 4.0
By: David Faucher 2 Replies
Presenting Cases to Referring Practitioners
By: Paul Moore 1 Reply
Installing 4.0 on Mac
By: Mike McKinley 6 Replies
Prep designs- minimal acceptable tooth structure retained
By: Brian Schaefer 3 Replies
Biocopy or not
By: Jay Henderson 4 Replies
Minimum occlusal thickness increase in 4.0
By: Loyd Dowd 4 Replies
Milling veneers
By: Brett Perry 4 Replies
Going back in 4.0
By: Mike McKinley 13 Replies
Contains Video Biocopy challenges...any suggestions?
By: Mike Maroon 11 Replies
Biocopy for a lone-standing tooth
By: Douglas Kear 15 Replies
Video on adding emax contact
By: Kent Mosby 4 Replies
Yellow undercut highlight
By: Michael Saso 2 Replies
Sometimes I have to stop and think about...
By: 11 Replies
model milling
By: Casey Gingrich 3 Replies
Managed Care and CEREC...Good Idea??
By: Meena Barsoum 12 Replies
Contacts fine on empress mill but tight on e-max
By: Mark Berdahl 3 Replies
Anterior Imaging and Biocopy Design - Part 1
By: Brad Woodring 3 Replies
virtual seat in 4.0
By: William Muldoon 8 Replies
Introduction to the Acquisition Tab
By: Robert Odegard 1 Reply
in lab
By: Leonard Packtor 3 Replies
Connect Bridge / Provisional in BioCopy?
By: Bob Conte 6 Replies
Information Overload
By: Loyd Dowd 8 Replies
Moving Images
By: Robert Odegard
3.8 inactive
By: Jim Finney 4 Replies
Inlay/ Onlay parameters 4.0
By: Greg Heideman 2 Replies
4.0 camera won´t initialize
By: Claus Donvang 15 Replies
New 3m blocks
By: Jim Overbay 3 Replies
Glaze question
By: Paul Goodman 1 Reply
Office Festivity
By: Peter Stickney 6 Replies
4.0 milling
By: William Muldoon 4 Replies
to use 4 or 3.8 for multiple veneers
By: Mark Gee 2 Replies
biogenic reference
By: david wang 8 Replies
no radio communication
By: Ray Morse 1 Reply
3.8 to 4.oh
By: Leonard Packtor 4 Replies
CEREC Study Club
By: Andrew Hall 25 Replies
Copy Line in 4.0 is very small
By: Stephen Glass 2 Replies
Cerec Update
By: Stephen Glass 11 Replies
Feels like Christmas
By: Jay Henderson 11 Replies
Maryland bridge
By: Jeff Siegert 1 Reply
A BIG thank you to Gregory Mark
By: Rich Rosenblatt, D.M.D. 12 Replies
E4D/CEREC NYU and CR reports
By: Mike Skramstad 4 Replies